20587 - SCTE Broadband Feb2020 COMPLETE v3
71 Vol. 42 No. 1 - February 2020 Issue from the archive transmis- sions, and if an exact spacing of 14MHz could not be achieved, it may not be possible to utilise all the channels shown on this diagram. A spacing of 14MHz here enables local oscillator radiation from the television receiver to fall between channels, thereby obviating the need to eliminate certain channels because of local oscillator radiation. As there were systems on the continent relaying as many as 10 television channels, and the likelihood was that this number would increase by at least 4, it became obvious that a bandwidth of about 300MHz would be required. The upper frequency limit of 300MHz results in a cable loss 15% greater than that at 230MHz. Any further increase in top frequency will result in a greater loss being incurred, and for this reason it was felt that any increase in upper frequency should be kept as small as possible. This also avoids the need for complete re-engineering of systems already installed. As a result of experimental work it became evident that existing transistors and techniques were quite capable of being extended to 300MHz. When upper frequency limits were taken very much higher, difficulties were encountered in the form of considerably reduced stage gain in the amplifiers and greater difficulty in obtaining good return loss performances. Satisfactory performance above about 300MHz would have resulted in a fairly sharp increase in cost. After carefully considering all the points mentioned it was decided to develop the equipment with a top frequency limit of 300MHz. Intermodulation Distortion As Fig.1 indicates we considered transmission systems which employed the whole of the bandwidth available, that is from the lowest frequencyof say44MHz to300MHz, encompassingnot onlyband I and band III, but using all the inter-band space and the space above band III, commonly referred to as the Super band. The use of this continuous spectrum immediately poses a problem. This is that the carriers of any two channels can beat together to produce a frequency which falls in another used part of the band. The difficulty has been minimised up to the present time by avoiding areas where various second order sum and difference intermodulation products occur. Fig.2 shows that second order intermodulation products are not a particular problem using standard Band I and Band III frequencies. If we take two frequencies in Band I, say 45MHz and 68MHz, and feed these into a non linear device such as an amplifier, these beat together to produce a frequency of 113MHz, which is outside the normal tele- vision bands. Two channels in Band III, for example channel ‘D’ and channel ‘13’, frequencies 215MHz and 175MHz produce a beat frequency of 40MHz, which is just below Band I. If slight offsets of the carrier frequencies are employed on these two channels, it is possible that a beat frequency can be produced in channel 1. However, under normal conditions the standard Band I and Band III channels do not produce intermodulation products at frequencies which cause interference. Some troublesome products can be generated by the beat frequencies between Band I and FM, for example between 42MHz and 100MHz, resulting in a product at 58MHz, which can fall onto a television channel. It has been common practice to run FM channels well below the level of television channels and also to use slight frequency offsets, thus avoiding any major second order intermodulation problems when using standard channels. It becomes apparent that if we use all the spectrum be- tween 40 and 300MHz, there are many possibilities of these beat frequencies falling within other channels. Two examples are shown in Fig.3. Taking channels at 140 and 150MHz (the inter-band) a beat frequency of 290MHz is produced. Similarly, two channels in the super-band of say 220MHz and 270MHz, would produce a difference frequency of 50MHz. Therefore, in order to make full use of the extended band available and to use the inter-band and super-band channels we must limit the amplitude of the second order, or, intermodulation products. These must be held at a level which will prevent visible distortion of the carrier at the point where the inter-modulation product falls. Most repeater amplifiers available prior to the develop- ment of the Oxford series had a somewhat poor performance in this respect. This in most cases resulted in visible inter- ference to carriers at or near the point where the beat frequency occurred. We could see that a very important requirement for the next generation of repeaters was that the second order intermodulation distortion should be such that the full bandwidth could be used, without the need for selecting and offsetting channels. The necessity for such selection and offsetting would limit the number of usable channels and the usefulness and versatility of the equipment. Fig.2. Fig.3.
Made with FlippingBook
RkJQdWJsaXNoZXIy OTIxNzg=