20587 - SCTE Broadband Feb2020 COMPLETE v3
70 Vol. 42 No. 1 - February 2020 Issue Introduction I would like to deal in some detail with the development of the Teleng Oxford range of Repeater Amplifiers. This Paper will be divided into three parts: the requirements of the system; the methods used to meet these requirements; and finally, the overall performance attained and the equipment which was produced as a result of this development project. When the Oxford project commenced we knew we were undertaking a very expensive development programme. Great care therefore was taken in deciding the parameters of the equipment which we were to produce, to ensure that as wide a market as possible would be available to this equipment. System Bandwidth The first question which had to be answered was, could the present VHF Band of 40 - 230MHz carry the number of programmes likely to be required during the foreseeable future. This question was asked of Britain, the European continent and the American continent. During our investigations it became apparent that the present 40 - 230MHz system could not cope with future requirements, particularly in continental Europe, America and Canada where the situation had already become difficult and where extra channel space would be required in the very near future. In Britain the situation at that time was somewhat easier but the many developments which were being discussed, and indeed, actively pursued indicated to us that within the next few years demand for extra channel space was likely to occur. Having decided that the 40 - 230MHz system was not adequate for all requirements we had to decide the Bandwidth to be used on the new equipment. We examined several systems in use in America. It be- came apparent that a top frequency of at least 270MHz was required to enable 30 channel working to be achieved on the American system. The situation in Europe is made more complex by the number of different television standards in use, the result is that adjacent channel operation cannot be employed at present and greater spacing - for example about 14MHz - must be left between vision carriers on the system. If we examine Fig.1, we can see that using a systemwith channels spaced at 14MHz even with 300MHz top frequency, we can only accommodate a maximum of 16 channels. This system is somewhat idealised as certain channels would have to be omitted due to local The Paper outlines reasons for extending the bandwidth to 300MHz and the extra problems this involved; refers to the required distortion figures for the new equipment, with particular reference to second order intermodulation; and describes the methods used in obtaining the improved figures and the measurement methods. Further topics are the automatic level control requirement on large systems, the types of automatic level control available, and the system finally used on the range of equipment under discussion. The provision of reverse transmission in the Band 5-30MHz is outlined, and finally the mechanical design considerations and choice of housing is discussed. by Chris Swires (Fellow) Swires Research & Development, Hornchurch, Essex. The Design Philosophy for a 5 - 300MHz Relay System - Part One Proceedings at meetings of The Society of Cable Television Engineers on 17th October 1972, at the Institution of Electrical Engineers, Savoy Place, London W.C.2, with Mr. P. Scadeng occupying the Chair and on 31st October 1972, at the Post House Hotel, Bramhope, Nr. Leeds, with the President of the Society, Mr. R. J. Seacombe, in the Chair. Chris Swires was born in Tadcaster near York, and educated at Tadcaster (Oglethorpe) Grammar School. He left Yorkshire to study at Enfield College of Technology and join Thorn Electrical Industries. He obtained his Higher National Certificate in Electrical Engineering and later, whilst still with Thorn, joined a group in its Transistor Applications Laboratory researching into the use of transistors in high frequency repeater amplifiers. As Senior Engineer, he developed a number of repeater amplifiers, for some of which he holds a patent. Before becoming Engineer in Charge of CATV Development, he developed Europe's first fully transistorised UHF to VHF converter. In early 1970, he joined Teleng as Manager of the Research and Development Laboratory, which has been responsible for a number of projects including development of the Teleng Derby Series, the Superverter (for which a patent is pending), and now the Oxford Series. He is married and lives in Essex. Fig.1. Channels spaced at 14MHz, 44 - 300MHz system from the archive To celebrate the SCTE's 75th anniversary year, we will be running one archive article in each issue of Broadband Journal in 2020.
Made with FlippingBook
RkJQdWJsaXNoZXIy OTIxNzg=